
SonoLayr is an acoustic nanofibre veil made by NanoLayr, the New Zealand company formerly known as Revolution Fibres. It is designed to add sound absorption to panels, linings and fabrics while adding almost no thickness or weight. It is a component for manufacturers, not a product you hang on your wall.
Here is what it is, what the company says it does, and how it compares with the materials you can buy today.
How it works
SonoLayr is made by electrospinning, a process that draws polymer into extremely fine fibres, far thinner than a human hair. Laid down as a veil, these fibres create a huge internal surface area. NanoLayr says one square meter of SonoLayr contains roughly 31 to 38 square meters of fibre surface. That large surface is where sound energy turns into tiny amounts of heat through friction.
The veil is usually laminated onto a carrier, such as a thin foam, a felt or a perforated panel. The company describes it as adding negligible thickness or weight to the panel.
Why thin absorbers are hard
Ordinary porous absorbers need depth to absorb lower frequencies. A useful rule is that they work well once their depth approaches a quarter of the wavelength, which is why bass traps are thick. Nanofibre layers aim to improve performance of thin assemblies, especially in the mid range, by adding a very fine, resistive layer. Research on nanofibre acoustic layers, including work by Revolution Fibres researchers, has shown gains in thin samples. (TechConnect Briefs)
It does not break the physics. A thin layer still cannot do the job of a deep bass trap, and an absorber does not block sound passing through a wall.
Where it is used
- Automotive interior linings and headliners.
- Aircraft and transport cabins, where weight matters.
- Thin acoustic panels and textiles for offices and interiors.
How it compares
| Material | Thickness | Absorption | Blocks sound | Available to consumers |
|---|---|---|---|---|
| SonoLayr veil on a carrier | Very thin | Improves thin assemblies | No | Mostly through manufacturers |
| Open-cell acoustic foam | 1 to 4 inches | Good for mid and high | No | Yes |
| Mineral wool panel | 2 to 4 inches | Very good, broad | No | Yes |
| Mass loaded vinyl | About 1/8 inch | No | Yes, a barrier | Yes |
Is it the “best and thinnest” soundproofing material?
It is one of the thinnest acoustic absorbers on the market, according to its maker. It is not a soundproofing barrier. If you want to stop noise from neighbors or traffic, you still need mass, sealing and decoupling. If you want to reduce echo at home, standard panels are easier to buy and well understood. See is 1 inch acoustic foam enough and our soundproofing materials guide.
Why the industry cares about thin absorbers
In cars, aircraft and electronics, every millimeter and gram counts. Traditional absorbers need depth, and depth means space and weight. A thin layer that improves absorption lets designers keep interiors quieter without adding bulk. That is where nanofibre veils are aimed.
What to ask before trusting performance claims
Like any acoustic product, nanofibre materials should come with test data.
- Absorption coefficient by frequency, usually measured in an impedance tube or reverberation room.
- The full test sample. A veil on a carrier is tested as a combination, so results depend on the carrier.
- Comparison with a baseline. The useful number is how much the veil adds compared with the same carrier without it.
What this means for homeowners
You will not find nanofibre veils in most hardware stores. If you want a quieter home today, the familiar options work well and are easy to buy:
| Your goal | Proven option |
|---|---|
| Less echo in a room | Fabric-wrapped mineral wool panels, open-cell foam, rugs, curtains |
| Less noise through a wall | Extra drywall, damping compound, sealing, decoupling |
| Quieter floor for neighbors below | Acoustic underlay rated for impact, rugs |
| Quieter car | Butyl damping mats, foam decoupler, mass barrier |
As thin absorbers become more common, expect to see them inside finished products such as ceiling tiles, office panels and car linings, rather than as a DIY material. For car projects, see our guide to car soundproofing.
FAQ
An electrospun nanofibre acoustic veil made by NanoLayr (formerly Revolution Fibres) in New Zealand. It is laminated onto other materials to add sound absorption.
It is mainly sold to manufacturers. You are more likely to find it inside a finished panel or lining than as a standalone product.
No. It is an absorber that reduces reflections. Blocking noise through walls requires mass and airtight construction.

Hello !
I live in France, in a 38 m² apartment. I’m thinking about soundproofing it, but I don’t know where to start. So I have load of questions :
– How much your material costs ?
– Can you send it in France without exploiding the transportation fees ?
– Do I have to pay customs duties and if it is a yes, then I much , exactly ?
– How do I install the Sonolayr paper on the ceiling, the wall and the floor : do I have to glue it on them like wallpaper ?
I’m looking forward to hear from you soon,
Best regards,
Nadège RUELLE
Angers, FRANCE